Control valve failure of the seven kinds of solutions

There are 7 kinds of solutions to the malfunction of the regulating valve during operation. During the operation of the regulating valve, there often occur such problems as jamming and jamming. Some even happen when they are put into operation. We have summarized some reasons and solutions For reference. 1, cleaning method Pipe in the welding slag, rust, slag, etc. in the throttle, guide parts, under the valve cover to balance the hole caused by blockage or stuck so that the valve surface, guide surface tension and scratches, sealing surface On the indentation and so on. This often occurs in the early delivery of new delivery systems and overhauls. This is the most common failure. In this case, you must uninstall the cleaning, remove the slag material, such as the sealing surface is also damaged should be ground; at the same time the bottom plug open to flush away from the balance hole into the valve cap slag material, and the pipeline Rinse. Put into operation before the valve is fully open, medium flow into the normal operation after a period of time. 2, external scouring method For some easy to sediment, the medium containing solid particles using ordinary valve adjustment, often in the throttle, the guide block, can be flush at the bottom of the bonnet flushing gas and steam. When the valve is clogged or stuck, open the external gas or steam valve, you can complete the flushing work in the case of the valve does not move, so that the valve normal operation. 3, the installation of pipe filters on the small-caliber control valve, especially the ultra-small flow control valve, the throttle clearance is very small, medium can not have a little slag material. In this case of blockage, it is best to install a filter on the valve before the pipeline to ensure the smooth passage of media. Control valve with locator, locator is not working properly, the air passage choke plug is the most common failure. Therefore, with the locator work, you must handle the gas source, the commonly used approach is to install the air filter regulator in front of the gas locator 4, to increase the throttle gap method such as the media of solid particles or pipes Washes off the welding slag and rust, etc. due to over throttle can cause blockage, stuck and other failures, can be used to throttle large gap throttling pieces - throttle area for the window, the opening of the spool, sleeve Tubes, because of their concentrated throttle area rather than their circumferential distribution, can easily be ruled out. If it is single, two-seater valve plunger can be changed to "V" -shaped spool, or into the sleeve valve. For example, a chemical plant often have a double-seat valve stuck, it is recommended to switch to sleeve valve, the problem was resolved immediately. 5, medium scouring method using the medium of its own scouring energy, erosion and easy to take away sedimentation, easy to block things, thereby enhancing the anti-blocking valve function. Common methods are: ① closed for the flow of closed-type use; ② the use of streamlined body; ③ the throttle placed in the erosion of the most powerful, using this method should pay attention to improve the erosion-resistant materials, parts erosion. 6, Straight through to the angle method Straight through the inverted S flow, flow path complex, upper and lower cavity dead zone, provides a place for the precipitation of the medium. Angular connection, like 90 ° elbow flow through the medium, erosion performance, small dead zone, easy to design streamlined. Therefore, the use of straight through the control valve can be slightly blocked when the valve can be used to change the angle 7, for the steam pipe valve sleeve, if the spool and sleeve gap is too small, or use different materials, it is likely because of expansion Coefficient of the different heat stuck. You can increase the gap in the appropriate processing (to meet the flow control requirements as a prerequisite), to prevent the occurrence of similar situations. More keyword search: Regulating valve

Round Molded Graphite

As the name implies, Round Molded Graphiteis a cylindrical product of graphite electrode, which is made of graphite block materials by crushing, screening, batching, shaping, cooling, roasting, dipping and graphitization of post section petroleum coke and medium temperature coal tar pitch. It has the advantages of high temperature resistance, corrosion resistance, good conductivity and light weight. It is mainly used for large DC resistance furnaces, blast furnace bricks, conductive electrodes, lining anti-corrosion and other purposes.

The high-purity graphite, graphite block and Molded Graphite produced by Pingdingshan Carbon Graphite Factory for many years are excellent, and the specifications of Round Molded Graphite are as follows: φ 450*800, φ 520*400 φ 630*420, φ 660*620 φ 780*600, φ 820*350~500 φ 900*350~400, φ 1050*350~400 φ 980~350*400, φ 1160*350~680 φ 1260*350~680, φ 1330*400 φ 1420*400, φ 1520*400 φ 1630*350, φ 1800*350 φ 2000*350, φ 520~2000*680

Round Rod Graphite,Graphite Round Stock,Round Molded Graphite,Graphite Round Square Shape

CARBONS TECH&CREATION(HENAN) INDUSTRY CO.,LTD , https://www.carbongraphitepart.com