1. In general measurement, when the wire is connected, first connect the line of the test sample to the test voltage and read the corona and stray current I during the test. Then, connect the test sample to the test voltage. Read total current I1; Leakage current of the test object: IO=I1-I'.
2. When it is necessary to accurately measure the leakage current of the test object, a high-voltage digital microammeter should be connected in series on the high voltage side.
The microampere meter must have a metal shield and should be shielded from the test object. The shielded lead-out of the high voltage lead should be tightly coupled with the shield at the meter end. If the performance of the product under test is to exclude the influence of the surface leakage current of the test object, it can be connected with the shielding of the high voltage lead after tightly winding the bare metal cord for a few turns at the high potential end of the test object.
3, DC high-voltage generator for zinc oxide, magnetic shock arrester and other test items can be disassembled under the ground, can also be used in the bottom of the test object (ground potential side) in series with ammeter to measure. When the influence of the surface leakage current of the test object is to be excluded, a bare bare copper wire can be used to wind several times around the ground potential end of the test object and be connected with the shielding of the shielded wire.
For small-capacity samples such as zinc oxide surge arresters, the discharge time is usually very short through the load resistor. Large-capacitance test items, such as cables, are generally subject to a test voltage of less than 20% of the test voltage, and discharges through the associated discharge bars. After the sample to be fully discharged, the grounding wire is hung to permit the removal of the high voltage lead and the replacement of the wiring work.
After the protection operation, the red light is off, the green light is on, and the voltage is decreased during the use. This is the protection action. At this point, the power switch should be turned off and all the panel lights should be off. The regulator will be returned to zero position, and after one minute the standby low-voltage capacitor is fully discharged before allowing the power switch to be turned on again. After re-doing the no-load test and ascertaining the situation, the test may be boosted again.
Dear Customer:
Thank you for your attention to our products. In addition to this product introduction, our company also introduces the vacuum tester, infrared thermometer, dielectric loss tester, high voltage test transformer, vacuum oil filter, high current generator, etc. If you are interested in our products, welcome to inquire. Thank you!
Features:
1).The beam uses light structural design, with good rigidity structure, light deadweight and small movement inertia.
2). The gantry structure, Y axis used dual-motor dual-driven system, X, Y, Z axis all use dual-straight rail that make the machine driving smoothly with high-precision.
3). Aiming at cutting three dimension LED character, trough metal panels and floor cutting, the accuracy can reach good indicators. Equipped with other advertise equipment (blister machine, engraving machine), forming the advertising word processing pipeline. Completely solve the traditional manual processing methods. Improve the efficiency of several times.
4). Cutting mouth is small, tidy, and avoid a second dressing processing.
5). It can apply to iron sheet the aluminum sheet, the galvanized sheet, hundred steel plates, metal plates and so on.
6). High cutting speed, high precision, and low cost.
7). The numerical control system disposes high, the automatic striking arc, the performance is stable.
8). Support ARTCAM software, Type3 produce standard G code way document, also can change software to read AUTOCAD software produce DXF form documents.
Application:
Advertising industry:
Advertising signs, logo making, decorative products, production of advertising and a variety of metal materials.
Metal industry:
For steel, Carbon Steel, Stainless steel, alloy steel, spring steel, copper plate, aluminum plate, gold, silver, Titanium and other metal plate and tube.
Plasma Cutter Sheet Metal Machine,Cnc Plasma Cutting Machines,Fast Speed Plasma Cutter Sheet Metal,Cnc Plasma Cutting Machine
HEBEI SENUF MANUFACTURE AND TRADE CO., LTD , https://www.senufmetals.com