 The washing and sweeping truck adopts Dongfeng Tianjin DFH1180EX8 type national six second category vehicle chassis modification, adding auxiliary engine, fan, high pressure water pump, clean water tank, trash can, left and right vertical sweep, wide suction nozzle with water spray rod, low pressure washing system, The sweeping dust suppression system, hydraulic system, special device electric control system and sub-frame etc. are refitted.
 The auxiliary engine drives the fan and high-pressure water pump, and the auxiliary engine uses a Dongfeng Cummins six-cylinder 170-horsepower diesel engine. The fan uses an 8.0 high-pressure centrifugal fan, which has high efficiency and large air volume, with a maximum air volume of 23,500m 3 /h. The high-pressure water pump adopts the internationally-known plunger pump with suitable flow and high pressure, and the maximum allowable pressure is 10MPa
Consultation hotline; 15271341199
 The clean water tank makes full use of the vehicle-mounted space, and has a large volume with a volume of 9m 3 . The trash bin adopts single stainless steel structure, dumping and unloading, with high-pressure self-cleaning device. The self-cleaning device can help unloading and cleaning the inside of the trash can when unloading the trash can.
 The left and right vertical scanning is a single scanning plate, which reduces the number of brushes and the consumption of brushes, and can reduce the cost of use. The left and right vertical sweeps are controlled separately, and different operation modes such as left sweep, right sweep and full sweep can be realized. The width of the suction mouth of the wide suction nozzle reaches 2418mm, ensuring that the total working width is greater than 3.5mm. The 4 height-adjustable nozzle wheels can adjust and ensure a reasonable gap between the nozzle and the road surface. The suction nozzle has a built-in high-pressure water spray rod, and as many high-pressure washing nozzles as possible are arranged inside the suction nozzle, which not only has a good cleaning effect, but also minimizes the secondary pollution caused by the high-pressure water flow.
 The left and right spray rods are installed on the suction cups and move up and down with the suction cups. The structure is simple and compact, which ensures that the height of the spray rods from the ground is constant and achieves the best cleaning effect. The open hydraulic system drives the left and right vertical sweeping and lifting, the left and right sweeping pan rotation, the suction nozzle lifting, the opening and closing of the rear door of the trash can, and the dumping and resetting of the trash can.
 The power take-off on the gearbox side of the chassis drives the low-pressure water pump to realize the low-pressure flushing function of the sprinkler, and one-button start and stop operations.
 The CSC5180TXSD6 sweeper has multiple functions such as road cleaning, road cleaning, curb cleaning, curb and curb facade scrubbing, low-pressure washing, spray dust removal, etc. There are multiple operation modes such as "full wash and sweep", "left wash and sweep", "right wash and sweep", "full sweep", "left sweep" and "right sweep" to choose from. Choose "full washing and sweeping" mode to clean the square and pavement, the cleaning efficiency is high and the effect is good, and the cleaning rate is more than 90%. Choose "left washing and sweeping" or "right washing and sweeping" mode to clean the road surface and curbs, and scrub the curb facade. When road cleaning or road cleaning operations are required, the road sweeping mode can be selected. When spray dust removal is required, the spray device can be turned on to perform spray dust removal operations. The road surface can be washed with low pressure like a sprinkler.
 CSC5180TXSD6 sweeper is suitable for cleaning operations such as mechanized cleaning, sweeping, spraying and dust suppression of urban roads, highways, squares, airports, docks, tunnels, bridges, isolation walls, curbs and curb facades.
Consultation hotline; 15271341199
Item | Main performance parameters | ||
Car type | Dongfeng Tianjin | ||
Vehicle model | CSC5180TXSD6 washing and sweeping truck | ||
Chassis model, category, manufacturer | DFH1180EX8 Class II Dongfeng Motor Co., Ltd. | ||
Emission Standards | GB3847-2005, GB17691-2018 National â…¥ | ||
hair move machine | Host | Chassis engine model and manufacturer | B6.2NS6B210 Cummins Engine Co., Ltd. |
Power (kw) | 154 | ||
Horsepower (ps) | 210 | ||
Displacement (ml) | 6200 | ||
Auxiliary engine | Clean engine model | Cummins 170 horsepower supercharged auxiliary engine | |
Power (kw) | 125 | ||
Horsepower (ps) | 170 | ||
Displacement (ml) | 5900 | ||
Fuel type | No. 0 light diesel (shared diesel tank with chassis) | ||
vehicle Basic parameter | Dimensions (length X width X height) mm | ★ 8630*2500*3100 | |
Wheelbase (mm) | 5000 | ||
Tires | 10.00R20 18PR steel wire tire | ||
Number of tires | 7 (including 1 spare tire) | ||
Wheelbase | Front wheel (mm) | 1876 | |
Rear wheel (mm) | 1820 | ||
Rated occupant | 3 people | ||
Front suspension/rear suspension (mm) | 1430/2220 | ||
Approach angle | 17° | ||
Departure angle | 13° | ||
Ground clearance (mm) | 320 | ||
Rated load (kg) | 5970 | ||
Curb weight (kg) | 11900 | ||
Maximum total mass (kg) | 18000 | ||
Â
 Dedicated performance parameters | Trash bin volume (m 3 ) | 7 | ||||
Clean water tank volume (m 3 ) | 9 | |||||
Sweeping width (mm) | 3000-3500 | |||||
Cleaning speed (km/h) | 3-15 | |||||
Cleaning operation speed (km/h) | 15-20 | |||||
Maximum cleaning capacity (m 2 /h) | 48000 | |||||
Suction capacity | Density (g/cm 3 ) | 2.0 | ||||
Mass (kg) | 1.5 | |||||
Suction particle size (mm) | ≥100 | |||||
Trash bin dump angle | ≥45° | |||||
Cleaning efficiency | ≥96% | |||||
Operating noise (db) | <Â 88 Meet the requirements of GB7258 | |||||
Driving performance parameters | Drive type | 4×2 rear axle drive | ||||
Suspension type | Leaf spring | |||||
Number of leaf springs (front/rear) | 8/10+7 | |||||
Braking type | Double circuit pneumatic brake, drum type | |||||
Braking distance (full load 30km/h) | ≤10m | |||||
Maximum speed (km/h) | 89 | |||||
Minimum turning radius (m) | 8 | |||||
Maximum grade | ≥30% | |||||
Clutch system | Single-plate dry-type diaphragm spring clutch, hydraulically operated | |||||
Transmission system | Mechanical 5-speed transmission with synchronizer, manual | |||||
Engine fuel consumption | Driving (L/100km) | Operation (L/h) | Operation (L/10000m 2 ) | |||
≤14 | ≤8 | ≤5 | ||||
Dust suppression system | Water spray form | Low pressure mist | ||||
Main components | Imported high-pressure pump, water filter, pipeline, stainless steel spray frame, high-pressure nozzle, etc. | |||||
High pressure pumps | CPX036 | |||||
Installation location | Sweeping and dust reduction | Scan the left and right front | ||||
Vacuum dust | In the suction cup suction port | |||||
Control type | Electronic control, one-key operation | |||||
Â
Hydraulic system | Type | Open, electric control centralized operation | |
Main components | Gear pumps, cycloid motors, hydraulic cylinders, solenoid valves, manifold blocks, high-pressure pumps, etc. | ||
Cycloid motor | Sanyo Motor | ||
gear pumps | Changyuan Machinery | ||
Hydraulic cylinder | Hypress hydraulic cylinder | ||
Hydraulic cylinder seals | Dingji | ||
Hydraulic tubing | Guangzhou Tianhe | ||
Solenoid valve group | Hypres (Sino-Italian joint venture) | ||
Shockproof pressure gauge | IMT | ||
Return oil filter | Sophia | ||
System overflow pressure | Mpa | 10-12 | |
Hydraulic oil tank volume | L | ≥60 | |
Electrical system | System composition | It is composed of chassis vehicle circuit, auxiliary engine electrical part and special working device operation control circuit. | |
Chassis vehicle system voltage (V) | twenty four | ||
Working device system voltage (V) | 12 | ||
Panel composition of electric control box | Auxiliary engine tachometer, auxiliary engine water temperature gauge, oil temperature alarm device, various operation control switches | ||
Control switch | Shanghai Schneider (Sino-French joint venture) | ||
Programmable Logic Controller | Bai Zhaofu | ||
breaker | Hager | ||
Battery model | Carbon Desorption1
Compared with similar products at home and abroad, this series of equipment has significant technical advantages, which are mainly reflected in:
1. High gold desorption rate: the carbon-poor gold grade after desorption is less than or equal to 50g/t (the same industry products are generally less than or equal to 100g/t).
2. High primary electrolysis rate: the average electrolysis rate of desorption solution is ≥90%. (The products in the same industry are generally around 70%).
3. Accurate gold balance: the actual amount of gold obtained after desorption and electrolysis is consistent with the theoretical gold content in the gold-loaded carbon. (Products in the same industry generally have the phenomenon of "floating gold or accumulative funds", which causes the loss of gold in the processing process and makes the amount of gold unbalanced)
4. Efficient and easy to operate: The whole set of equipment adopts integrated design, signal acquisition, operation adjustment control and safety protection are automated to ensure high efficiency, easy operation, safety and reliability during the entire operation period.
5. Low operating cost: The equipment is made of real materials of special materials (mainly including high-quality insulation materials, all-tetrafluoroethylene insulation materials, fully imported aerospace-grade circulating pumps, high-resistance electric shock heating pipes, etc.). The power-consuming equipment adopts frequency conversion design to ensure the low cost of operation and maintenance while ensuring the desorption electrolysis index.
Carbon Desorption1,Electrolytic Refining Of Gold,Gold Mining Machine,Extraction Of Gold,Electrowinning For Gold Changchun Gold Research Institute Co.LTD , https://www.changchunmachine.com | ||