Factory Oxygen Generator Oxygen Concentrator

Factory oxygen generator oxygen concentrator
1. Principle:
PSA oxygen generator uses clean compressed air as raw material and zeolite molecular sieve (ZMS) as 
sorbent, to produce oxygen gas with Pressure Swing Adsorption (PSA) technology in normal 
temperature. Comparing with oxygen, nitrogen is preferentially adsorbed by ZMS while at high pressure. 
ZMS releases adsorbed nitrogen at low pressure, which is called regeneration. The oil free and dustfree 
compressed air enters one of the two adsorption towers filled with ZMS. Nitrogen is adsorbed ZMS micro 
pores and then retained and leaves oxygen as product gas. When ZMS in one tower is saturated with 
nitrogen, the adsorption tower is depressurized and ZMS is regenerated for next cycle. While one tower 
finishes the cycle, the other adsorption tower starts to work. With control on/off state of the pneumatic valve 
by PLC, to separate nitrogen and oxygen gas, and create continuous flow of oxygen with required purity.
2. Industrial PSA oxygen generator features:
Skid structure, easy installation.
When oxygen generator reaches site, just connect the air compressor into main machine, then with one
simple touch on the start, the whole machine starts to work, no need for site installation, site training,etc. No
need for Gamma engineers go to site, further saving customer's cost.
Special filling device
Making the fill of molecular sieve achieve max density and evenness. Getting rid of carbon molecular sieve
creeping and wearing and "tunnel effect" from the root. Therefore the molecular sieve has longer lifetime,
higher utility ratio and lower material air consumption.
Special gas distributors
Equipped at both top and bottom side of the adsorption tower adapting multi-layer hole plate structure and
special hole arrangement. These makes gas distribution within tower more efficient.
Pipeline flow speed control technology
Making the molecular sieve avoid damage caused by collision by "boiling" at the top of adsorption tower, no
need extra pressing device.
3. How to get a prompt quotation of oxygen machine:
When you send the inquiry to us, pls kindly send it with below technical information.
1) O2 flow rate: _____Nm3/hr( or How many cylinders do you want to fill per day(24hours))
2) O2 purity: _____%
3) O2 discharge pressure: _____Bar
4) Voltages and Frequency : ______V/PH/HZ
5) Application:
4. FAQ:
    Q: OEM/ODM, or customers logo printed is available?
    Yes, OEM/ODM, customers logo is welcomed.
    Q:  Delivery date?
    Usually 30 work days after receiving deposit, specific delivery date based on order quantity
    Q: what's your payment terms?
    Advanced payment 30% TT and 70% TT balance before shipping, Western Union, Paypal, other payment 
    terms also can be discussed based on our cooperation.
    Q: How to control your quality?
    We have professional QC team, control the quality during the mass production and inspect the completely
    goods before shipping.
    Q:  If we don't have shipping forwarder in China, would you do this for us?
    We can offer you best shipping line to ensure you can get the goods timely at best price.
5. Contact Yujia:


  Factory oxygen generator oxygen concentrator
1. Principle:
PSA oxygen generator uses clean compressed air as raw material and zeolite molecular sieve (ZMS) as 
sorbent, to produce oxygen gas with Pressure Swing Adsorption (PSA) technology in normal 
temperature. Comparing with oxygen, nitrogen is preferentially adsorbed by ZMS while at high pressure. 
ZMS releases adsorbed nitrogen at low pressure, which is called regeneration. The oil free and dustfree 
compressed air enters one of the two adsorption towers filled with ZMS. Nitrogen is adsorbed ZMS micro 
pores and then retained and leaves oxygen as product gas. When ZMS in one tower is saturated with 
nitrogen, the adsorption tower is depressurized and ZMS is regenerated for next cycle. While one tower 
finishes the cycle, the other adsorption tower starts to work. With control on/off state of the pneumatic valve 
by PLC, to separate nitrogen and oxygen gas, and create continuous flow of oxygen with required purity.
2. Industrial PSA oxygen generator features:
Skid structure, easy installation.
When oxygen generator reaches site, just connect the air compressor into main machine, then with one
simple touch on the start, the whole machine starts to work, no need for site installation, site training,etc. No
need for Gamma engineers go to site, further saving customer's cost.
Special filling device
Making the fill of molecular sieve achieve max density and evenness. Getting rid of carbon molecular sieve
creeping and wearing and "tunnel effect" from the root. Therefore the molecular sieve has longer lifetime,
higher utility ratio and lower material air consumption.
Special gas distributors
Equipped at both top and bottom side of the adsorption tower adapting multi-layer hole plate structure and
special hole arrangement. These makes gas distribution within tower more efficient.
Pipeline flow speed control technology
Making the molecular sieve avoid damage caused by collision by "boiling" at the top of adsorption tower, no
need extra pressing device.
3. How to get a prompt quotation of oxygen machine:
When you send the inquiry to us, pls kindly send it with below technical information.
1) O2 flow rate: _____Nm3/hr( or How many cylinders do you want to fill per day(24hours))
2) O2 purity: _____%
3) O2 discharge pressure: _____Bar
4) Voltages and Frequency : ______V/PH/HZ
5) Application:
4. FAQ:
    Q: OEM/ODM, or customers logo printed is available?
    Yes, OEM/ODM, customers logo is welcomed.
    Q:  Delivery date?
    Usually 30 work days after receiving deposit, specific delivery date based on order quantity
    Q: what's your payment terms?
    Advanced payment 30% TT and 70% TT balance before shipping, Western Union, Paypal, other payment 
    terms also can be discussed based on our cooperation.
    Q: How to control your quality?
    We have professional QC team, control the quality during the mass production and inspect the completely
    goods before shipping.
    Q:  If we don't have shipping forwarder in China, would you do this for us?
    We can offer you best shipping line to ensure you can get the goods timely at best price.
5. Contact Yujia:


 

Semi Automatic Vacuum Forming Machine

Semi Automatic Vacuum Forming Machine applications

Suitable for PVC, PE, PET, PETG, PP, PC, PS, HIPS, APET etc, the machine furnace produce heat to soften the plastic sheet, then vacuum pump sucks the plastic sheet down to the forming mould area to finish the forming, different forming mould enable to have different forming shape. This machine is ideal for the sample making purpose and small quantity order production.

Semi automatic Vacuum Forming Machine features

1. 25pcs ceramic infrared heating boards which can be controlled separately, suit for different size or different thickness material.
2. 25pcs Solid state voltage regulators, control heating boards simple and visualized.
3. Large-scale cooling fan which can cool the products quickly.
4. Water-spray cooling system which suit for thick material.(optional)
5. Manual and Semi-auto style.

Semi automatic vacuum forming machine parameters

Model	HX-61B
Power supply	AC380V
Power	12.5KW
Max.forming size	560*610mm
Max. forming height	200mm
Speed	200~300moulds/H
Thickness of material	0.2~1.5mm
N. weight	650KG
Machine size	1800*1200 *2000mm

Semi Automatic Vacuum Forming Machine

Semi Automatic Vacuum Forming Machine,Semi-Automatic Plastic Forming Machine,Semi Automatic Vaccum Blister Forming Machine,Semi-auto Blister Forming Machine

ShenZhen Hengxing Machinery Factory , http://www.szchxjx.com